This article mainly introduces:

Italy hydraulic cylinder,swager cylinder manufacturer,swager cylinder

(Italy swager cylinder,produced by Hengyu Hydraulic Co., Ltd）

swager cylinder are widely used in Italy，because of no need for deceleration device，long service life，smooth movement.So our company has designed swager cylinder for customers from Italy.

Introduction to swager cylinder:

The swager cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the swager cylinder should pay attention to: the operation should be as far away from the swager cylinder as possible, to avoid falling objects, knocking, rubbing the swager cylinder coating. When cleaning the swager cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the swager cylinder when the oil temperature exceeds 70 ° C.

The coordination of the sliding parts of the swager cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

In the case of serious wear on the inner surface of the swager cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the swager cylinder manufacturing process for replacement. The swager cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Improve the service life of the swager cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the swager cylinder (such as the swager cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the swager cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the swager cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single swager cylinder exhaust.

Answers to some questions about swager cylinder:

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.