This article mainly introduces:

Egypt hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Egypt tension cylinder,produced by Hengyu Hydraulic Co., Ltd）

tension cylinder are widely used in Egypt，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed tension cylinder for customers from Egypt.

Introduction to tension cylinder:

How to repair the tension cylinder body when it is damaged: When the tension cylinder has trace deformation and shallow tensile marks, the tension cylinder is repaired by strong honing process. The heavy honing process can repair tension cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the tension cylinder can meet the technical requirements.

tension cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards tension cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the tension cylinder guide is determined by the length of the stroke. Check the strength of tension cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

Causes and countermeasures of oil tension cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the tension cylinder will lead to premature wear of the piston seal, replace the piston seal; If the tension cylinder is visibly scarred, the tension cylinder must be replaced. It can be pressurized at one end of the tension cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most tension cylinder piston drift may not come from the tension cylinder, the above method to determine the tension cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

When the tension cylinder needs to be stored for a period of time, please follow the recommended methods: The tension cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tension cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tension cylinder should not be in direct contact with water vapor for a long time. The tension cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tension cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tension cylinder Before working, the tension cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tension cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about tension cylinder:

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

What is hydraulic cylinder internal leakage and external leakage?
The internal leakage of the hydraulic cylinder refers to the leakage of the piston head seal of the double-acting cylinder, and the leakage occurs inside the cylinder; The external leakage refers to the leakage phenomenon between the cylinder head (or cylinder guide sleeve) and the plunger rod (or piston rod) and the seal between the guide sleeve and the cylinder block, and the oil in the hydraulic cylinder leaks to the outside.