九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Bangladesh

Release time:2023-11-12 14:24:17 Hits: Current position: Home > News

This article mainly introduces:

Bangladesh hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Bangladesh track steering cylinder

(Bangladesh track steering cylinder,produced by Hengyu Group)

track steering cylinder are widely used in Bangladesh,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed track steering cylinder for customers from Bangladesh.

Introduction to track steering cylinder:

The machining accuracy of the track steering cylinder depends on the level of equipment, production technology and testing means. track steering cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

When the track steering cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the track steering cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil track steering cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical track steering cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the track steering cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The track steering cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure track steering cylinder can use 20 steel pipe, and the high pressure track steering cylinder can use 45 steel pipe.

track steering cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about track steering cylinder:

How to choose cylinder size, pump type, motor power for a 30-ton press?
30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.

The difference between the overall cylinder and the separate cylinder of the truck?
The whole cylinder is cast in one piece, and such a cylinder generally does not leak oil. Split cylinder refers to two welded, easy to leak oil in the welding place, resulting in damage to the cylinder, or its body can not get up, many people do not use this kind of cylinder now.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP