九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

plating press hydraulic cylinder Sold to Colombia

Release time:2023-11-12 14:24:15 Hits: Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,plating press hydraulic cylinder manufacturer,plating press hydraulic cylinder

Colombia plating press hydraulic cylinder

(Colombia plating press hydraulic cylinder,produced by Hebei Hengyu company)

plating press hydraulic cylinder are widely used in Colombia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed plating press hydraulic cylinder for customers from Colombia.

Introduction to plating press hydraulic cylinder:

In the process of using the plating press hydraulic cylinder, sometimes such a problem will occur, the plating press hydraulic cylinder can not act immediately after the instruction of the plating press hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil plating press hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

There are some honeycomb holes in the inner wall of the plating press hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the plating press hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the plating press hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the plating press hydraulic cylinder is targeted to prevent. Is very necessary.

When the oil pressure of the plating press hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

If it is found that the plating press hydraulic cylinder lubrication is poor or the plating press hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the plating press hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the plating press hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the plating press hydraulic cylinder center line. In this way, when the piston works in the plating press hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the plating press hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

Answers to some questions about plating press hydraulic cylinder:

How many boom cylinders, bucket rod cylinders and bucket cylinders are there in a small single-bucket excavator?
one for bucket, one for forearm, only one piece for a small excavator under the big arm, two pieces for medium and large excavator.

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP