九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Kenya

Release time:2023-11-10 08:35:04 Hits: Current position: Home > News

This article mainly introduces:

Kenya hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Kenya stern plate hydraulic cylinder

(Kenya stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Kenya,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stern plate hydraulic cylinder for customers from Kenya.

Introduction to stern plate hydraulic cylinder:

The stern plate hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the stern plate hydraulic cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The stern plate hydraulic cylinder is basically composed of stern plate hydraulic cylinder and stern plate hydraulic cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

The pressure of the sliding surface of the stern plate hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the stern plate hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

When the stern plate hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the stern plate hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil stern plate hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical stern plate hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the stern plate hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The repair method of the stern plate hydraulic cylinder: the repair of the stern plate hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about stern plate hydraulic cylinder:

Why can't the hydraulic cylinder be replaced with water?
Hydraulic oil for hydraulic transmission has a variety of requirements for viscosity, density, flow rate, and temperature, which are not available for water.

What does cylinder speed ratio mean?
The speed ratio of the cylinder is the ratio of the reciprocating speed of the piston, equal to the ratio of the rodless cavity area to the roded cavity area.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP