九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

sanitation truck hydraulic cylinder Sold to Sweden

Release time:2023-12-09 16:24:26 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,sanitation truck hydraulic cylinder manufacturer,sanitation truck hydraulic cylinder

Sweden sanitation truck hydraulic cylinder

(Sweden sanitation truck hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

sanitation truck hydraulic cylinder are widely used in Sweden,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed sanitation truck hydraulic cylinder for customers from Sweden.

Introduction to sanitation truck hydraulic cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the sanitation truck hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The material of the sliding part of the sanitation truck hydraulic cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

How to determine the working pressure of the sanitation truck hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, sanitation truck hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

sanitation truck hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

Answers to some questions about sanitation truck hydraulic cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

What factors does the movement speed of the cylinder in the hydraulic system depend on?
The hydraulic system should be the piston movement in the cylinder, and the speed should also be the speed of the piston, according to the piston speed formula: v=4qm/pai*(D^2-d^2) where q is the flow rate of the input hydraulic cylinder, m is the volumetric efficiency of the hydraulic cylinder, D, d is the diameter of the piston and piston rod, because other factors are determined, the movement speed of the cylinder depends on the flow rate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP