Release time:2023-11-08 08:12:19 Hits: Current position: Home > News
This article mainly introduces:
Slovenia hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder(Slovenia unidirectional cylinder,produced by Hengyu Hydraulic Co., Ltd)
unidirectional cylinder are widely used in Slovenia,because of long service life,smooth movement,high work efficiency.So our company has designed unidirectional cylinder for customers from Slovenia.
How to determine the working pressure of the unidirectional cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, unidirectional cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.
Analysis of commonly used seals: The wear ring and slip ring commonly used on the unidirectional cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.
After the unidirectional cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.
If the seal of the unidirectional cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and unidirectional cylinder, and the phenomenon of "pulling the unidirectional cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.
What valve is used to control cylinder expansion?
Mainly use reversing valve, but the details of the control need hydraulic control valve, hydraulic control valve can be divided into direction control valve, pressure control valve, flow control valve. The valve controls the expansion of the cylinder is the direction control valve, that is, the reversing valve. What is the meaning of two-position three-way and three-position four-way of the reversing valve? Usually according to the different working positions that can stay after the spool is moved, it can be divided into: two-position valves, three-position valves and multi-position valves. According to the number of different slide valve channels can be divided into: two-way valve, three-way valve, four-way valve, five-way valve and multi-way valve. The name of the reversing valve is called the multi-position and multi-pass reversing valve according to its working position and the number of channels.
How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.