九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Finland

Release time:2023-11-21 09:55:58 Hits: Current position: Home > News

This article mainly introduces:

Finland hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Finland steering power cylinder

(Finland steering power cylinder,produced by Hengyu Hydraulic Co., Ltd)

steering power cylinder are widely used in Finland,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed steering power cylinder for customers from Finland.

Introduction to steering power cylinder:

The oil steering power cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the seal of the steering power cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the steering power cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

The machining accuracy of the steering power cylinder depends on the level of equipment, production technology and testing means. steering power cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

Answers to some questions about steering power cylinder:

What are the cylinder manufacturing processes?
Hydraulic cylinder processing process: 1, cylinder: a, material preparation (seamless steel pipe) → inspection (material certificate, etc.) → tempering (outsourcing: Some parts) → car (car round, shelf mouth, boring, flange stop, etc.) → tempered hardness test → welding (welded pipe joint base, flange and other accessories) → boring or honing (rough boring, fine boring, rolling) → car (hole slot or internal and external thread) → fitter (drilling) → inspection → rust prevention storage b, material preparation (forgings) → inspection (material certificate, inspection, etc.) → welding (blank butt welding) → welding inspection → car (rough car) → quality control (outsourcing: some parts) → car (car round, shelf mouth, boring stop, flange stop, etc.)

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP