九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to El Salvador

Release time:2023-11-16 08:44:17 Hits: Current position: Home > News

This article mainly introduces:

El Salvador hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

El Salvador synchronous hydraulic cylinder

(El Salvador synchronous hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

synchronous hydraulic cylinder are widely used in El Salvador,because of excellent fatigue and impact resistance,long service life,no need for deceleration device.So our company has designed synchronous hydraulic cylinder for customers from El Salvador.

Introduction to synchronous hydraulic cylinder:

How to determine the working pressure of the synchronous hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, synchronous hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The definition of the minimum stable speed refers to the minimum movement speed of the synchronous hydraulic cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the synchronous hydraulic cylinder that undertakes different work has different requirements for the minimum stable speed.

When the synchronous hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

The synchronous hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the synchronous hydraulic cylinder should pay attention to: the operation should be as far away from the synchronous hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the synchronous hydraulic cylinder coating. When cleaning the synchronous hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the synchronous hydraulic cylinder when the oil temperature exceeds 70 ° C.

Answers to some questions about synchronous hydraulic cylinder:

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

What is the material of the hydraulic cylinder slider?
Three parts of the hydraulic cylinder are essential, which are: cylinder - cylinder head assembly, piston - piston rod assembly, and sealing device. When you say slider, you mean piston. - Piston rod. Piston materials commonly used gray cast iron, wear-resistant cast iron, aluminum alloy (assembled), etc., can also be used 35 and 45 steel (integral). The piston rod is generally made of 35 and 45 steel. When the impact vibration is large, alloy steel such as 55 steel or 40Cr is used.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP