九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Slovakia

Release time:2023-11-13 11:19:49 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Slovakia stern plate hydraulic cylinder

(Slovakia stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Slovakia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed stern plate hydraulic cylinder for customers from Slovakia.

Introduction to stern plate hydraulic cylinder:

The stern plate hydraulic cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

When purchasing the stern plate hydraulic cylinder, try to clarify the following parameters of the stern plate hydraulic cylinder: A. stern plate hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or stern plate hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right stern plate hydraulic cylinder type can be found accurately and quickly.

The stern plate hydraulic cylinder should be vented: when the stern plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the stern plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the stern plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the stern plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the stern plate hydraulic cylinder. stern plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When installing the stern plate hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stern plate hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the stern plate hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stern plate hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stern plate hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stern plate hydraulic cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

What is the role of the cylinder on the plastic mold? The oil cylinder plays a great role in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the oil cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product, sometimes customers require to use hot runner, the price is more expensive, but there are many benefits. It can save raw materials and shorten the molding cycle.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP