九九精品國產99精品_亚洲最大无码中文字幕_國產av一區二區網址_国产成人精品一 二区_亚洲一区邻居人妻有码中文_特三级黄色毛片_国产免费午夜福利在线观看_国产真实伦实例_性欧美牲交图片三级黄频_午夜在线亚洲

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Panama

Release time:2023-11-12 15:30:15 Hits: Current position: Home > News

This article mainly introduces:

Panama hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Panama swager cylinder

(Panama swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Panama,because of no need for deceleration device,long service life,smooth movement.So our company has designed swager cylinder for customers from Panama.

Introduction to swager cylinder:

The swager cylinder can not be used as grounding electrode to avoid electric damage to the piston rod.

When the swager cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the swager cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil swager cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical swager cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the swager cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The oil swager cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

When the swager cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the swager cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the swager cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the swager cylinder can meet the requirements by grinding. However, the life and reliability of this repair swager cylinder are not high.

Answers to some questions about swager cylinder:

What kind of seal ring we should choose for 120Mpa hydraulic cylinder?
The sealing rings used in mining machinery are high pressure, which can reach 150MPa. It is generally composed of three parts, the guide ring, the sealing body and the elastomer. It's not a special structure. It's more mature. Usually said mountain circle, bud circle.

What are the standard cylinder models for hydraulic cylinders?
National standard GB/T2348-1993 specifies the hydraulic cylinder inner diameter series, you can check GB/T2348-1993 relevant regulations.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP